Posts

Transmitter Prototype

A previous channel principle of the Q-Strip was based on an Arduino, Seeeduino LoRaWAN development board and then I tested a feather board, both boards are stable but in my opinion too big. At the moment I am working on a LoPy module that is even smaller and well portable.
Every 2 minutes the LoraWan transmitter sends a signal with the measured values ​​of the connected moisture sensor. This signal goes to the LoRaWAN Gateway and then is collected in a database.
[ngg_images source=”galleries” container_ids=”4″ display_type=”photocrati-nextgen_basic_thumbnails” override_thumbnail_settings=”0″ thumbnail_width=”240″ thumbnail_height=”160″ thumbnail_crop=”1″ images_per_page=”20″ number_of_columns=”0″ ajax_pagination=”0″ show_all_in_lightbox=”0″ use_imagebrowser_effect=”0″ show_slideshow_link=”1″ slideshow_link_text=”[Diavoorstelling tonen]” order_by=”sortorder” order_direction=”ASC” returns=”included” maximum_entity_count=”500″]

Hardware prototype

Een eerder zender principe van de Q-Strip was gebaseerd op een Arduino, Seeeduino LoRaWAN development board en vervolgens heb ik een feather board getest, beide boards werken stabiel maar zijn mijnsziens nog te groot. Daarom de LoPy module die klein goed “draagbaar” is.Andere experiment boards zoals de Sodaq Explorer en The Things Uno zijn ook zeer goed bruikbaar en volledig arduino compatible. Beide boards zijn uitgerust met een Microchip LoRaWAN module.
De data
Iedere 2 minuten geeft de LoraWan zender een signaal af met de gemeten waarden van de aangesloten vochtssensor. Dit signaal gaat naar de LoRaWAN Gateway om vervolgens te worden verzameld in een database bij The Things Network
[ngg_images source=”galleries” container_ids=”4″ display_type=”photocrati-nextgen_basic_thumbnails” override_thumbnail_settings=”0″ thumbnail_width=”240″ thumbnail_height=”160″ thumbnail_crop=”1″ images_per_page=”20″ number_of_columns=”0″ ajax_pagination=”0″ show_all_in_lightbox=”0″ use_imagebrowser_effect=”0″ show_slideshow_link=”1″ slideshow_link_text=”[Diavoorstelling tonen]” order_by=”sortorder” order_direction=”ASC” returns=”included” maximum_entity_count=”500″]

De LoRaWAN Gateway

De LoraWan Gateway module is met een bridge op een Raspberry pi 3 gezet en aangesloten met SMA connector naar de buitenantenne. Op deze Raspberry draait Jessie image. De packetforwarder scriptings van TheThingsNetwork zijn gebruikt om alle LoRa data van de gateway te versturen naar “de cloud”. Vanaf hier kan alle data weer opgehaald worden om te tonen in rapportages of live op aan te sturen. Dus signalen terug te sturen naar de sensor !
[ngg_images source=”galleries” container_ids=”2″ display_type=”photocrati-nextgen_basic_thumbnails” override_thumbnail_settings=”0″ thumbnail_width=”240″ thumbnail_height=”160″ thumbnail_crop=”1″ images_per_page=”20″ number_of_columns=”0″ ajax_pagination=”0″ show_all_in_lightbox=”0″ use_imagebrowser_effect=”0″ show_slideshow_link=”1″ slideshow_link_text=”[Diavoorstelling tonen]” order_by=”sortorder” order_direction=”ASC” returns=”included” maximum_entity_count=”500″]

The LoRaWAN Gateway

The LoraWan Gateway module is set with a bridge on a Raspberry pi 3 and connected with SMA connector to the outdoor antenna. Raspberry is running Jessie image on this Raspberry. The packetforwarder scriptings from TheThingsNetwork are used to send all LoRa data from the gateway to “the cloud”. From here all data can be retrieved to show in reports or live on. So send signals back to the sensor!
[ngg_images source=”galleries” container_ids=”2″ display_type=”photocrati-nextgen_basic_thumbnails” override_thumbnail_settings=”0″ thumbnail_width=”240″ thumbnail_height=”160″ thumbnail_crop=”1″ images_per_page=”20″ number_of_columns=”0″ ajax_pagination=”0″ show_all_in_lightbox=”0″ use_imagebrowser_effect=”0″ show_slideshow_link=”1″ slideshow_link_text=”[Diavoorstelling tonen]” order_by=”sortorder” order_direction=”ASC” returns=”included” maximum_entity_count=”500″]